Hunter Douglas Remote Flashing? What Each Blinking Light Means
A blinking PowerView remote is telling you something specific. Match the pattern below and you will know what it wants in under a minute.
We sell battery wands, not remotes, so there is no reason for us to steer you anywhere but the truth: most blinking remotes just want two new coin cells.
Why are the numbers on my Hunter Douglas remote blinking in sequence?
That is the low-battery warning on a PowerView Gen 3 remote (the generation shipped from spring 2022).
When the group numbers light up one after another, or blink when you press a button, the cells are too weak to send a command reliably. Hunter Douglas notes the pattern looks a lot like the one you see while syncing — but if you were not syncing anything, it means batteries.
Fix: replace both CR2032 cells. The remote keeps every group and favorite through the change; there is nothing to re-program afterwards.
Why do the lights on my Legacy PowerView remote flicker?
Same message, older remote. On a Legacy PowerView Pebble remote (everything before fall 2022), the two signs Hunter Douglas lists for weak cells are:
- lights that flicker instead of lighting cleanly
- a remote that keeps reverting to group one on its own
A tired remote fails slowly. First it works across the room but not across the house, then only sometimes, then not at all. If that is the story, it is the cells.
Fix: lift the module out of the Pebble cradle, twist the back cover off with a coin, and fit two new CR2032 cells both positive side up. The same orientation for both trips people, because plenty of two-cell devices alternate them. These do not.
Why is the whole remote blinking after I held STOP?
Because you put it into programming mode. On a Legacy PowerView remote, pressing and holding STOP for about six seconds until the lights blink is the deliberate way in — it is the first step of pairing a shade, adding a repeater or changing a shade's direction.
If you got there by accident, holding STOP again until the blinking stops takes it back out. If you got there on purpose, the pairing steps are on how to reset a Hunter Douglas remote and re-pair the shade.
Why did the group buttons flash twice?
On Legacy remotes, two flashes of the group buttons is a confirmation: the remote just finished copying its settings from another remote (hold ALL on the new remote, press STOP on the old one). Nothing is wrong. If you expected the flash and did not get it, Hunter Douglas suggests fresh cells in both remotes and a second try.
Why is there a red light blinking on the shade, not the remote?
Then the remote is fine, and the shade is the one talking.
A PowerView shade that blinks its red LED at the end of every move is saying its own batteries — the AA cells in the battery wand — are running down. It will keep working for a while, slower each week, and then stop. That one is covered on Hunter Douglas blinds not working? troubleshooting guide, and the battery count that tells you which wand you have is on which batteries?.
A red light on a hub or repeater is a network fault, not a shade fault, and not something a new part fixes.
The remote lights up fine — but the shade does nothing
Then the remote has done its job and the problem is at the shade. Two possibilities, and a ten-second test tells them apart.
Press the small programming button on the shade's headrail.
- The shade moves or jogs — it has power. It has simply lost its pairing with the remote, which Hunter Douglas says can happen when a shade's power supply is poor (weak cells, or a wand not seated). Re-pair it; that costs nothing. Steps are on the reset and re-pair page.
- Nothing — no travel, no jog, no sound — the shade has no power. That is the AA cells, the battery wand or the cable, and the remote cannot help. Start with is it the wand?.
The remote does not light up at all
No lights on any button means no power at the remote: cells flat, cells upside down, a cover not fully twisted on, or — on a brand-new Gen 3 remote — the two plastic battery tabs were never pulled. Fix those in that order. If it still shows nothing with fresh cells fitted correctly, the remote itself has failed, and Hunter Douglas or your original dealer is the place to go.
Which wand do I need?
Only relevant if the shade turned out to be the problem. Count the batteries in the old wand.
- Twelve AA — the 18V wand, part 7520068000
- Eight AA — the 12V wand, part 7520069000
The full picture is in the battery wand replacement guide.
What we stock
- 18V battery wand — twelve AA, part 7520068000
- 12V battery wand — eight AA, part 7520069000
- Battery tube conversion kit — eight AA, for sealed tubes
- Motor to wand power cable — PowerRise, 13 inch
We do not sell remotes, hubs or repeaters. All new, genuine Hunter Douglas stock, shipped free within the United States, same business day on orders placed before 3pm Eastern.
Still stuck? Call (609) 474-4242 weekdays 9am–5pm Eastern, or email a photo of your headrail sticker to support@batterywands.com. We will tell you which part it takes — including when the answer is that you do not need one.
Replacement parts. Complete your repair.
Common parts for Hunter Douglas motorized shades.
