How to Raise a Hunter Douglas Motorized Shade With Dead Batteries
Updated
You raise it by giving it power, not by pulling it. Put fresh batteries in the wand, or borrow a working wand with the same battery count from another shade, then press the button on the headrail and the shade goes up. Hunter Douglas does not document a way to wind a standard PowerView or PowerRise shade up by hand, and for its motorized arches and angled shades it says outright that there is no manual override.
Already know it is the wand? Genuine 18V and 12V wands from $17.95 ↓
The one exception is the SkyLift skylight shade, which Hunter Douglas lets you nudge up a few inches by hand to reach its batteries. That is covered below.
How do I reach the battery wand when the shade is down?
On Duette and Applause shades, Hunter Douglas clips the standard AA wand to the back channel of the headrail, with the shade's power cable plugged into a socket on the wand. It sits on the headrail rather than in the fabric, so you can usually reach it from behind with the shade down. Unplug the cable from the wand and take the wand out of its clip.
On Designer Roller, Designer Screen and Designer Banded shades the wand hangs behind the fabric. Hunter Douglas's steps:
- Raise the fabric if you can, to make room behind the shade
- Reach carefully behind the fabric, usually on the same side as the motor
- Find the wand by feel, without tugging or bending the fabric
- Pull the wand downward to release it from its bracket
- Unplug the cable from the wand only, never from the shade itself
A satellite battery pack, mounted on the wall or sill beside the window, is reached directly.
How do I get power back to it?
- AA wand: a full set of fresh batteries, twelve or eight, all the same brand, following the diagram printed on the tube. Never top up a mixed set
- No batteries in the house? A wand from another shade works, as long as it holds the same number of cells. Twelve AA runs a twelve-cell shade, eight runs an eight-cell one
- Rechargeable wand: the Single Charger can charge it in place, without taking it out of the shade. A red light means charging; green means done. If nothing lights, the charging guide has the fixes
- C-size satellite wand: make sure it is clipped firmly into its metal bracket, which completes the circuit, and fit fresh alkaline C cells
The full battery change, with the mistakes people make, is on how to change the batteries in Hunter Douglas blinds.
Which button raises the shade?
Once it has power, you do not need the remote. Use the button on the shade:
- PowerView Gen 3 Duette and Applause: the control button on the bottom of the right-side end cap. Each press lowers, stops or raises the shade in turn. On Top-Down/Bottom-Up and Duolite shades it steps through the bottom rail and the middle rail
- Legacy PowerView: press and release the programming button on the headrail once. A shade with power travels all the way up or down
- PowerRise: the manual button on the side of the headrail, below it, or on a satellite eye. Press once to move the shade, press again to stop it
Press and release. Holding the button down for several seconds starts a calibration reset instead, which is useful later but not what you want right now.
Can I lift a SkyLift shade by hand?
A little, and only to reach the batteries. Duette and Applause SkyLift shades keep their battery wands in the bottom rail. Hunter Douglas's method when the fabric is down and the motor is not working:
- Wrap two straight edges, such as old credit cards, in a cloth so they do not mark anything
- Slide one in at each end, where the moving rail meets the stationary bottom rail
- Push both ends up together, firmly but gently, no more than six inches
- Take the cover off the stationary bottom rail and unplug and remove the wands
SkyLift shades take lithium AA, not alkaline: 16 Energizer Ultimate Lithium in the bottom-rail wands, or 12 in a rear-mounted satellite pack, because skylights get hot.
It has fresh power and still will not go up
Then work out which of these it is:
- It goes down but not up. Raising takes more current than lowering, so this is still weak power, most often a wand losing voltage at corroded contacts. See shade won't go up or down
- It stops short of the top. Hunter Douglas's first step is the calibration reset: hold the programming button for about six seconds until the shade jogs, release, and let it run fully open and fully closed. After that come the limits, and then the dealer
- You can hear the motor but nothing moves. Hunter Douglas says to contact the installer or dealer. Power is reaching the motor, so a new wand will not help
- It works, then forgets its programming. Unplug the power cable between the shade and the power source, wait 10 seconds, and plug it back in
When the wand is the problem
If fresh, correctly installed batteries leave the shade silent, or a borrowed wand runs it and its own does not, the wand has failed. Count the battery channels in it:
- Twelve AA means the 18V battery wand, part 7520068000
- Eight AA means the 12V battery wand, part 7520069000
Both are genuine Hunter Douglas parts at $17.95, with free UPS Ground shipping, usually 1 to 6 business days, and 30-day returns. Fitting one takes a couple of minutes and no tools.
Questions people also ask
Can I just pull the fabric up?
No. Hunter Douglas documents no hand-lift for its standard motorized shades, and the only manual lift it describes, on SkyLift, is capped at six inches. We would not force one. Restore power instead.
Will the shade remember its settings after the batteries die?
Usually, yes. The pairing and the travel limits are stored in the motor, and Hunter Douglas's battery change steps include no re-pairing. If it ignores the remote afterward, re-pair it.
What if the shade is too high to reach?
Hunter Douglas offers a satellite battery pack that mounts on a wall or sill and is meant for shades in high windows. Ask the dealer about adding one, so the next battery change happens at arm's length.
Replacement parts. Complete your repair.
Common parts for Hunter Douglas motorized shades.



